Why Understanding Essential Plumbing Skills is Essential When Installing a Bathtub
Why Understanding Essential Plumbing Skills is Essential When Installing a Bathtub
Blog Article
The article in the next paragraphs relating to Tools You Need to Install a New Bathtub is particularly informative. Read it for your own benefit and figure out what you think about it.
Setting up a tub isn't precisely rocket science, however it does need strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bath tub with a new one is additionally a reasonably difficult job. If the old bathtub is conveniently accessible, the task can relocate easily; if you need to open up a wall to remove the old tub and also place the new bathtub, the job is a lot harder. In either situation, the job is within a home handyman's abilities, although you will certainly need an assistant to leave the old tub and also set in the brand-new one. See to it you have actually certified yourself for the job and are comfortable trying it. Instead of working with a contractor to take control of a halfway-completed job, it is far better to think about using one prior to you start. Possibilities are you might need an expert plumber to make tube connections.
This write-up will assist you mount a new tub in your bathroom if you have currently acquired a new tub as well as do not need to transform the setup of your previous supply of water pipelines.
Your devices and also material checklist ought to make up the following:
Preparing for the Setup
First of all, the supporting framework supplied with the bath must be fitted (if needed) according to the maker's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets system to avoid stress on the bathtub.
Fit the flexible faucet ports to the bottom of the two taps making use of 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you use all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be fitted in its last placement.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you need to do is separate the water system. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The process of eliminating the existing taps can be quite problematic due to the limited gain access to that is often the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a towel prepared for the continuing to be water that will originate from the pipelines. Once the supply pipes have actually been removed, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from transforming during this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing compound.
Before carrying on to fit the brand-new faucets, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Making use of both wooden boards under its feet, position the bathtub in the needed setting. The wooden boards are useful in equally spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 tiny points.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level as well as adjusting the feet on the bathtub till the spirit level reads level.
To mount faucets, fit the bottom of the outermost flexible tap port to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Switch on the water and also check all joints and also new pipework for leakages and also tighten them if necessary. Fill up the bath tub as well as also check the overflow electrical outlet and also the typical electrical outlet for leaks.
Lastly, repair the bath paneling as defined in the manufacturer's user's manual. Tiling as well as sealing around the bathtub should wait till the bath tub has been used a minimum of once as this will resolve it right into its final setting.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end offers a link to the current supply pipes.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin making sure that the washing machines are in area between the faucet and also the sink. Protect the faucet in position with the producer given backnut. When the tap is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet connectors. The previous kind should be linked to the tap ends initially, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a stiff seal, triggering the water to pass through the wall in between the bath and also the tiling, leading to problems with moisture and also possible leakages to the ceiling below.
You can select from a range of coloured sealants to assimilate your fixtures and fittings. They are marketed in tubes and cartridges, as well as are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the bathtub with water prior to sealing, to permit the movement experienced when the tub remains in usage. The sealer can split relatively early if you do not consider this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise quickly available on the marketplace. It is advisable to fit the floor tiles using waterproof or water-proof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate reading about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try to leave a comment down the page. We would be pleased to know your ideas about this post. Hoping that you visit us again in the future. Enjoyed our write-up? Please share it. Let another person discover it. Kudos for your time. Kindly pay a visit to our site back soon.
For quick fixes, call! Report this page